User Tools

Site Tools


homebrew_cnc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Last revisionBoth sides next revision
homebrew_cnc [2016/04/23 18:09] – [Power Supplies] tanzseglerhomebrew_cnc [2016/06/01 18:19] – [Cost To Use] tanzsegler
Line 13: Line 13:
  
 ===== Cost To Use ===== ===== Cost To Use =====
-  * $5/hr+  * $5/hr runtime
 ===== Specs ===== ===== Specs =====
  
Line 36: Line 36:
     * <del>5.7V, 1.6A, 1.8 degrees/step, current limited - running 24v</del>     * <del>5.7V, 1.6A, 1.8 degrees/step, current limited - running 24v</del>
     * One of original X,Y motors burned out, they have been replaced with:     * One of original X,Y motors burned out, they have been replaced with:
-  * X,Y-axis [[http://www.automationtechnologiesinc.com/products-page/stepper-motors/kl23h286-20-8b|NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B)]]+  * X,Y-axis [[http://www.automationtechnologiesinc.com/products-page/stepper-motors/kl23h286-20-8b|NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B)]] wired in series
     * {{:equipment:wiringDiagram_KL23H286-20-8B.pdf|NEMA23 Wiring diagram}}     * {{:equipment:wiringDiagram_KL23H286-20-8B.pdf|NEMA23 Wiring diagram}}
   * Z-axis ALM 90130-25-SPA stepper motor   * Z-axis ALM 90130-25-SPA stepper motor
Line 46: Line 46:
 ==== Controller Board ==== ==== Controller Board ====
   * [[https://github.com/synthetos/TinyG/wiki|TinyG v8]]   * [[https://github.com/synthetos/TinyG/wiki|TinyG v8]]
 +    * {{https://camo.githubusercontent.com/f82917a94b87bc98750b96f4303d0018a6ece26b/687474703a2f2f6661726d332e737461746963666c69636b722e636f6d2f323837332f31303836333833303138335f353739393939613330635f6f2e706e67|TinyG board diagram}}
 ==== Bits ==== ==== Bits ====
   * 1/4 to 1/8 step down collet.   * 1/4 to 1/8 step down collet.
   * We have a few 1/8" cutting head, 1/8" shank, chipbreaker bits.   * We have a few 1/8" cutting head, 1/8" shank, chipbreaker bits.
   * Please provide your own bits if you wish to do anything precise.   * Please provide your own bits if you wish to do anything precise.
 +
 +==== Helpful Documents ====
 +  * {{:equipment:cnc_operatinginstructions.doc|Homebrew CNC Operating Instructions}}
 +  * {{:equipment:cnc_easel_gcodegeneration.doc|Gcode generation from Easel}}
  
 ===== History ===== ===== History =====
  
 +day/month/year\\
 17/04/2016 Started a timeline\\ 17/04/2016 Started a timeline\\
 2015       Acquired Homebrew CNC from Milwaukee Makerspace\\ 2015       Acquired Homebrew CNC from Milwaukee Makerspace\\
Line 59: Line 64:
 20/02/2016 CNC router operational. \\ 20/02/2016 CNC router operational. \\
 25/03/2016 X axis stepper motor overheating.\\ 25/03/2016 X axis stepper motor overheating.\\
-17/04/2016 Purchased 3NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B)\\+17/04/2016 Purchased 3 NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B) TY James Pittman!\\
 17/04/2016 Replaced X,Y steppers with NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B)\\ 17/04/2016 Replaced X,Y steppers with NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B)\\
 +23/04/2016 Switched X,Y steppers from parallel to series. Power draw was too high in parallel.\\
homebrew_cnc.txt · Last modified: 2022/05/29 16:01 by 127.0.0.1