equipment:tablesaw_steelcity
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
equipment:tablesaw_steelcity [2017/01/18 03:53] – tab tanzsegler | equipment:tablesaw_steelcity [2022/05/29 16:01] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 10: | Line 10: | ||
Blade Diameter: 10" | Blade Diameter: 10" | ||
- | Spindle | + | Arbor Diameter: 5/8" |
Rail Length: 52" | Rail Length: 52" | ||
- | {{:equipment:tablesaw_steelcity_manual.pdf|Manual}} | + | Tilt: Left |
+ | |||
+ | [[http:// | ||
===== Manufacturer Specifications: | ===== Manufacturer Specifications: | ||
- | Manufacturer: | + | Manufacturer: |
- | + | ||
- | Manufacturer' | + | |
- | + | ||
- | Manufacturer' | + | |
- | + | ||
- | Style (Type): | + | |
- | + | ||
- | Spindle Speed (RPM): | + | |
- | + | ||
- | Maximum Spindle Diameter (In.): | + | |
- | + | ||
- | Spindle Size Under Nut (In.): 3/4 (3.42), 1-1/4 (5.15) | + | |
- | + | ||
- | Spindle Travel (In.): 4 | + | |
- | + | ||
- | Spindle Tilt (Deg.): | + | |
- | Reversible: Yes | + | Manufacturer' |
- | Table Opening Diameter (In.): 7.33 | + | Manufacturer' |
- | Table Inserts (In.): 2.55, 4.16, 5.75 | + | Motor: 1-3/4 HP TEFC, 120V/240V |
- | Table Size (In.): 40 x 30 | + | Amps: 15/7.5 |
- | Table Travel | + | Dimensions Wx Dx H (In.): 84 x 31 x 35 |
- | Table Height from Floor (In.): 35-1/2 | + | Table Material: Granite |
- | Sliding Table Size (In.): N.A. | + | Switch Type: Paddle |
- | Fence Size (L x H) (In.): 18-3/4 x 4-7/8 | + | Blade Diameter |
- | Fence Travel (Major and Minor) (In.): N.A. | + | Blade RPM: 3450 |
- | Dust Port Outside Diameter | + | Arbor Size (In.): 5/8 |
- | Dust Collection Minimum CFM Required (CFM): 600 | + | Tilt: Left |
- | Electrical Controls: Yes | + | Max Depth of Cut at 90 degree(In.): 3-3/8 |
- | Motor Power (HP): 5 | + | Max Depth of Cut at 45 degree(In.): 2-1/4 |
- | Motor Phase: 3 | + | Rip Right of Blade(In.): 36 |
- | Motor Voltage | + | Rip Left of Blade(In.): 20 |
- | Prewired Voltage | + | Table in Front of Blade(In.): 12-1/ |
- | Wiring Remarks: Requires 460V Magnetic Switch | + | Dado Capacity(In.): 13/16 |
- | Motor Current | + | Table Size (In.): with extension table 27 * 80 |
- | Recommended Circuit Size (Amps.): 20/10 | + | Dust Port (In): 4 |
equipment/tablesaw_steelcity.txt · Last modified: 2022/05/29 16:01 by 127.0.0.1