The Bodgery Wiki

User Tools

Site Tools

Trace: • howto_connect_the_doorbot
homebrew_cnc

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
homebrew_cnc [2016/04/18 05:15] – tanzseglerhomebrew_cnc [2022/05/29 16:01] (current) – external edit 127.0.0.1
Line 1: Line 1:
 ====== CNC Router - Homebrew ====== ====== CNC Router - Homebrew ======
 ~~NOTOC~~ ~~NOTOC~~
 +{{ :equipment:CNC_homebrew.jpg?400|}}
  
-Make/Model+===== Make/Model =====
  
 Original machine was custom built by Ron Bean and Tom Gondek at Milwaukee Makerspace. Since it has arrived at The Bodgery it has been rebuilt and modified primarily by Alex Kovell, Tony Roman, and Chris Kaufmann. Original machine was custom built by Ron Bean and Tom Gondek at Milwaukee Makerspace. Since it has arrived at The Bodgery it has been rebuilt and modified primarily by Alex Kovell, Tony Roman, and Chris Kaufmann.
  
-Specs+===== Training Required ===== 
 +This is a red tag tool. You MUST BE TRAINED before using it.
  
-//Software// +Contact Alex Kovell or Tony Roman to set up an appointment for your training.
-//G-code is sent to the board via browser based [[http://chilipeppr.com/tinyg|Chilipeppr]].// +
-//[[https://github.com/chilipeppr/serial-port-json-server|Serial Port JSON Server]] is required to send the G-code.//+
  
-Work area 24" x 32.5"+===== Cost To Use ===== 
 +  * $5/hr runtime 
 +===== Specs =====
  
-(1) Dewalt DWP611 Compact Router (http://www.dewalt.com/tools/woodworking-routers-dwp611.aspx)+==== Software ==== 
 +  * G-code is sent to the board via browser based [[http://chilipeppr.com/tinyg|Chilipeppr]]. 
 +  * [[https://github.com/chilipeppr/serial-port-json-server|Serial Port JSON Server]] is required to send the G-code.
  
-//Amps 7.0Amps// +==== Work Area ==== 
-//Horsepower 1-1/4HP// +  * 24" x 32.5"
-//No Load Speed 16,000-27,000rpm// +
-//Collet Diameter 1/4"// +
-//Spindle Lock 12 position// +
-//Tool Weight 4.6lbs//+
  
 +==== Cutting Tool ====
 +  * [[http://www.dewalt.com/tools/woodworking-routers-dwp611.aspx|Dewalt DWP611 Compact Router]]
 +    * Amps         7.0Amps
 +    * Horsepower 1-1/4HP
 +    * No Load Speed 16,000-27,000rpm
 +    * Collet Diameter 1/4"
 +    * Spindle Lock 12 position
  
-(2) <del>Oriental Motor Co. VEXTA C6244-9212K stepper motors</del> (X,Y axes) 
-<del>5.7V, 1.6A, 1.8 degrees/step, current limited - running 24v</del> 
-One of original X,Y motors burned out, they have been replaced with: 
-NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B) http://www.automationtechnologiesinc.com/products-page/stepper-motors/kl23h286-20-8b 
-Wiring diagram: TODO link to pdf here 
  
 +==== Stepper Motors ====
 +  * <del>Oriental Motor Co. VEXTA C6244-9212K stepper motors (X,Y axes)</del>
 +    * <del>5.7V, 1.6A, 1.8 degrees/step, current limited - running 24v</del>
 +    * One of original X,Y motors burned out, they have been replaced with:
 +  * X,Y-axis [[http://www.automationtechnologiesinc.com/products-page/stepper-motors/kl23h286-20-8b|NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B)]] wired in series
 +    * {{:equipment:wiringDiagram_KL23H286-20-8B.pdf|NEMA23 Wiring diagram}}
 +  * Z-axis ALM 90130-25-SPA stepper motor
 +    * 5.7V, 1.6A, 1.8 degrees/step, current limited - running 24v
  
-(1) ALM 90130-25-SPA stepper motor (Z-axis)+==== Power Supplies ==== 
 +  * Microtel SP-150-24IER power supplies 
 +    * 150 watt, 115vAC/1ph/60Hz 2.5 amp input, 24VDC 6.3 amp output. 
 +==== Controller Board ==== 
 +  * [[https://github.com/synthetos/TinyG/wiki|TinyG v8]] 
 +    * {{https://camo.githubusercontent.com/f82917a94b87bc98750b96f4303d0018a6ece26b/687474703a2f2f6661726d332e737461746963666c69636b722e636f6d2f323837332f31303836333833303138335f353739393939613330635f6f2e706e67|TinyG board diagram}} 
 +==== Bits ==== 
 +  * 1/4 to 1/8 step down collet. 
 +  * We have a few 1/8" cutting head, 1/8" shank, chipbreaker bits. 
 +  * Please provide your own bits if you wish to do anything precise.
  
-5.7V, 1.6A, 1.8 degrees/step, current limited - running 24v +==== Helpful Documents ==== 
- +  * {{:equipment:cnc_operatinginstructions.doc|Homebrew CNC Operating Instructions}} 
-(2) Microtel SP-150-24IER power supplies +  * {{:equipment:cnc_easel_gcodegeneration.doc|Gcode generation from Easel}}
- +
-150 watt, 115vAC/1ph/60Hz 2.5 amp input, 24VDC 6.3 amp outputny +
- +
-(3) TinyG v8 controller board +
- +
-Bits +
-1/4 to 1/8 step down collet. +
-We have a few 1/8" cutting head, 1/8" shank, chipbreaker bits. +
-Please provide your own bits if you wish to do anything specific or precise. +
- +
-History +
- +
-17/04/2016 Started a timeline +
-2015 Acquired Homebrew CNC from Milwaukee Makerspace +
-2015 Purchased TinyG v8 controller board +
-17/04/2016 Replaced X,Y steppers with NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B)+
  
 +===== History =====
  
 +day/month/year\\
 +17/04/2016 Started a timeline\\
 +2015       Acquired Homebrew CNC from Milwaukee Makerspace\\
 +2015       Purchased TinyG v8 controller board\\
 +20/02/2016 CNC router operational. \\
 +25/03/2016 X axis stepper motor overheating.\\
 +17/04/2016 Purchased 3 NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B) TY James Pittman!\\
 +17/04/2016 Replaced X,Y steppers with NEMA23 425oz/in 2.8A Stepper Motor ¼” Dual shaft (KL23H286-20-8B)\\
 +23/04/2016 Switched X,Y steppers from parallel to series. Power draw was too high in parallel.\\
homebrew_cnc.1460956533.txt.gz · Last modified: 2022/05/29 16:01 (external edit)