equipment
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
equipment [2023/04/23 04:30] – [Craft] - removing tools that aren't available Erin K | equipment [2023/05/03 00:56] (current) – Shawn Southard | ||
---|---|---|---|
Line 163: | Line 163: | ||
//Email: blacksmithing@thebodgery.org// | //Email: blacksmithing@thebodgery.org// | ||
+ | <WRAP center round important 60%> | ||
NOTE: This area is not currently available for use. | NOTE: This area is not currently available for use. | ||
+ | </ | ||
+ | |||
* Propane Forge, Single Burner | * Propane Forge, Single Burner | ||
Line 186: | Line 189: | ||
// | // | ||
- | | + | |
- | * [[equipment: | + | |
- | * Band Saws - Wilton Vertical 14" (Model 8201), Grizzly Horizontal (Model 60561) | + | * DRO installed (though not very accurate) |
- | | + | * Quick-change tool post |
- | * Drill Press - Grizzly 17" Floor Model (Model G7947) | + | * Tail-stock accepts Morse Taper 2 |
- | | + | - South Bend 13" |
- | * Buffer - Dayton 10" Buffer (Model 3NYA6), | + | * Quick-change tool post |
- | * DROs - DRO PRO Mill Model, DRO PRO Lathe Model | + | * Tail-stock accepts Morse Taper 3 |
- | * Rotary Table - Grizzly Rotary Table (Model 250) | + | - Chucks |
+ | * 3-jaw chuck | ||
+ | * 4-jaw chuck | ||
+ | * 6-jaw chuck | ||
+ | * collet chuck | ||
+ | * steady rest in various states | ||
+ | - Assortment of carbide-insert and HSS tooling | ||
+ | - Band Saws | ||
+ | | ||
+ | - Grizzly Horizontal (Model 60561) | ||
+ | | ||
+ | | ||
+ | * DRO installed (and quite accurate) | ||
+ | * Bridgeport-style knee mill | ||
+ | * Accepts R8 tooling/ | ||
+ | - [[equipment: | ||
+ | * Max travel | ||
+ | * X: 10" | ||
+ | * Y: 6" | ||
+ | * Z: 10" | ||
+ | * Max spindle RPMs | ||
+ | * 10000 RPM | ||
+ | * Uses ER40 tooling | ||
+ | * Pneumatic drawbar | ||
+ | * Plexiglass enclosure | ||
+ | * Variety of tooling available | ||
+ | * Haimer probe available | ||
+ | * Z tool-height setter switch | ||
+ | - Grizzly Mill/Drill (Model G0463) | ||
+ | - Grizzly Rotary Table (Model 250) | ||
+ | - Rotary indexer + tail-stock available | ||
+ | - Variety of | ||
+ | | ||
+ | * Fly-cutters | ||
+ | * Drills | ||
+ | * Parallels | ||
+ | * Clampsets | ||
+ | * Stops | ||
+ | * etc | ||
+ | - Drill Press | ||
+ | | ||
+ | | ||
+ | | ||
+ | * As of 04/2023: has wire wheel and coarse grinding wheel | ||
+ | - Buffer | ||
+ | | ||
+ | * As of 04/2023: has scotch-brite wheel and buffing wheel | ||
+ | | ||
+ | | ||
+ | | ||
+ | - (Unknown) Grade B Granite Surface Plate | ||
+ | - Height gauge available with training | ||
+ | - Grizzly 0-6" Micrometer set (with standards), available with training | ||
+ | - Dial indicators with magnetic stands | ||
+ | * These are not in the best condition but good enough for most work | ||
+ | - Indocol mill spindle clamp for dial test indicators | ||
+ | - Assortment of gauges/ | ||
+ | * Thread gauges | ||
+ | * Telescoping bore gauges | ||
+ | * etc | ||
+ | |||
+ | ---- | ||
+ | |||
+ | |||
+ | ===== Plastics ===== | ||
+ | //Area Captain: Karen Corbeill// | ||
+ | |||
+ | |||
+ | * Purple t-shirt press | ||
+ | * Toaster Oven | ||
+ | * Page laminator | ||
+ | * Craft-style heat gun | ||
+ | * Wen rotary tool + bits | ||
+ | * Scroll saw (owner: Karen) | ||
+ | * Tabletop bandsaw | ||
+ | * Large vertical bandsaw with 12” throat (owner: Karen) | ||
+ | * Drill press + full set of drill bits | ||
+ | * Cordless Dewalt drill | ||
+ | * Large vacuum former | ||
+ | * Small vacuum former (owner: Johnny Yan, machine currently stored in 3D printing) | ||
+ | * Small diameter wood chipper/ | ||
+ | * Tabletop hot wire knife | ||
+ | * Handheld hot knife | ||
+ | * Handheld hot wire knife | ||
+ | * Hot glue gun | ||
+ | * UV flashlight | ||
+ | * 2x small space heaters (for resin curing) | ||
+ | * Steel file sets (large and needle) | ||
+ | * Acrylic sheet cutter/ | ||
+ | * Aviation shears | ||
+ | * Laser thermometer gun | ||
+ | * Small griddles and mug warmers | ||
+ | * Modified paper/ | ||
Line 291: | Line 386: | ||
* Small Bolt Cutters | * Small Bolt Cutters | ||
* Shop Vacs/Dust Removal | * Shop Vacs/Dust Removal | ||
- | * Air Compressor - 150 max psi, 17gal, 1.7hp | + | * Screw Compressor - 150 max psi, 17gal, 1.7hp |
+ | * Compressed air pumped to: | ||
+ | - [[area: | ||
+ | - [[area: | ||
+ | - [[area: | ||
+ | - [[area: | ||
+ | - [[area: | ||
+ | - [[area: | ||
+ | - [[area: | ||
+ | - [[area: | ||
+ | * More extensions planned for the future | ||
equipment.1682224223.txt.gz · Last modified: 2023/04/23 04:30 by Erin K